How to Fix Sunbeam Electric Blanket Blinking

Home » Electric Blanket » How to Fix Sunbeam Electric Blanket Blinking

If your Sunbeam electric blanket starts blinking, there are a few things you can do to try to fix it. First, check the power cord and make sure it’s plugged in properly. If it is, then unplug the power cord and plug it back in again.

This sometimes clears the problem. If that doesn’t work, then you’ll need to open up the control panel and look for any loose wires. Once you find the loose wire, reattach it and see if that fixes the problem.

If not, then you may need to replace the control panel entirely.

  • Remove the blanket from the bed and unplug it from the electrical outlet
  • Inspect the power cord for any damage, such as frayed wires or exposed insulation
  • If the cord is damaged, it will need to be replaced
  • Check to make sure that the connections between the power cord and the blanket are secure
  • Plug the blanket back in and turn it on
  • If it still blinks, contact Sunbeam customer service for further assistance

How Do I Fix My Sunbeam Electric Blanket Blinking F2

If your Sunbeam electric blanket is blinking F2, it means that the blanket is overheating. This can happen for a number of reasons, including if the blanket is too close to another heat source, such as a radiator or fireplace. It can also happen if the blankets control unit is faulty.

To fix this problem, first try moving the blanket away from any other heat sources. If that doesn’t work, then you will need to replace the control unit. You can do this yourself by following these steps:

See also  Can Electric Blanket Raise Body Temperature


1) Unplug the power cord from the wall outlet and remove any batteries from the control unit. 2) Remove the screws that hold the control unit in place on the blanket. 3) Pull out the old control unit and insert the new one in its place.

4) Screw the new control unit into place and reinsert any batteries. 5) Plug the power cord back into the wall outlet and turn on the blanket.

How to Fix Sunbeam Electric Blanket Blinking

Credit: www.youtube.com

Why Does My Sunbeam Electric Blanket Keep Flashing?

If your Sunbeam electric blanket is flashing, it could be for a few different reasons. First, check to make sure that the power cord is plugged in securely to both the outlet and the blanket. If it is, then unplug the power cord from the outlet and plug it back in again.

This can sometimes reset the connection and stop the flashing. If the power cord is plugged in correctly and the problem persists, there could be an issue with your blanket’s heating element. To test this, unplug the power cord from both the outlet and the blanket.

Then remove one of the wires from one of the heating elements (located on either side of the blanket near where you would lay your head). Plug the power cord back into boththe outlet andtheblanket, making sure thatthe bare wireis not touching anything metal. Iftheblanketstops flashing,thenyouknowthat there was an issue with that particular heating element and you’ll needto replacethe element by following these instructions: http://www.sunbeamservice.com/en-US/Replacement_Parts/Blankets_and_Comforters/Pages/Electric_Blanket_Replacement_Element_(2).

aspx

Why is My Sunbeam Heating Pad Blinking?

If your Sunbeam heating pad is blinking, it may be due to a loose connection. Check the power cord and make sure it’s plugged in securely. If the problem persists, try resetting the heating pad by unplugging it for 30 seconds.

See also  How Many Amps Does an Electric Blanket Use

How to fix your heated blanket flashing red light

Conclusion

If your Sunbeam electric blanket is blinking, there are a few things you can do to fix it. First, check the power cord and make sure it is plugged into a working outlet. Next, check the control panel to make sure all the settings are correct.

Finally, if the problem persists, contact Sunbeam customer service for assistance.